User Tools

Site Tools


m0dul

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Last revision Both sides next revision
m0dul [2011/06/20 20:49]
127.0.0.1 external edit
m0dul [2011/06/20 23:04]
kiu [Single M0duls]
Line 9: Line 9:
 ===== Interface ===== ===== Interface =====
  
-{{:dual-m0dul.brd.png?​direct&​200|}} {{:​single-m0dul.brd.png?​direct&​200|}}+m0dul can be connected to the r0ket via the m0dulbusThe connectors are in 2.54mm/100mil spacing, prepopulated with female socketsIf available, a __stackthrough connector__ should be used to interface with the m0dulbus. The hackerbus is intended for tinkering, a m0dul should use the __m0dulbus only__.
  
-A m0dul can be connected to the r0ket via the m0dulbus. The connectors are in 2.54mm/100mil spacing, prepopulated with female sockets. If available, a __stackthrough connector__ should be used to interface with the m0dulbus. The hackbus is intended for tinkering, a m0dul should use the __m0dulbus only__.+<note tip>​Stackthrough connectors kits (2x 2x06) will be on sale at the campsite!<​/note>
  
-Please be aware that __above__ the __m0dulbus__ connectors the __LCD__ and __button__ is located - this area should __not be covered__ by your m0dul. Go for the sides and below the connectors :)  +The //m0dul A// and //m0dul B// connectors are rotated 180 degrees to each other. If your m0dul is symmetric/has no orientation requirements,​ it can be plugged both ways. Keep in mind though that the chip select pins on //A// and //B// differ (that should be configurable via defines in your software).
- +
-As the m0dulbus connectors are __not reverse polarity protected__,​ you should __document__ (eg marking your connector with a 1) how your m0dul should be plugged onto the r0ket. +
- +
-The //m0dul A// and //m0dul B// connectors are rotated 180 degrees to each other. If your m0dul is symmetric ​and has no orientation requirements,​ it can be plugged both ways. Keep in mind though that the chip select pins on //A// and //B// differ (that should be configurable via defines in your software).+
  
 ^ m0dul A ^ m0dul B ^ ^ m0dul A ^ m0dul B ^
Line 26: Line 22:
 Links: [[https://​github.com/​r0ket/​r0ket/​tree/​master/​hardware/​m0dul|Eagle]] Links: [[https://​github.com/​r0ket/​r0ket/​tree/​master/​hardware/​m0dul|Eagle]]
  
-Almost any m0duls can be combined, if you offer the possibility to change the adress (e.g. with solder bridges). Have a look at already existing [[m0duls|m0duls]] to find out which standard ​adresses ​are still free/​little ​uses, enter your own standard adress!+Almost any m0duls can be combined, if you offer the possibility to change the adress (e.g. with solder bridges). Have a look at already existing [[m0duls|m0duls]] to find out which standard ​addresses ​are still free/​little ​used - enter your own [[m0duls#​registry|address]]! 
 + 
 + 
 +Please be aware that __above__ the __m0dulbus__ connectors the __LCD__ and __button__ is located - this area should __not be covered__ by your m0dul. Go for the sides and below the connectors :)  
 + 
 +As the m0dulbus connectors are __not reverse polarity protected__,​ you should __document__ (eg marking your connector with a 1) how your m0dul should be plugged onto the r0ket. 
 + 
 +==== Dual M0duls ==== 
 +A dual m0dul uses both m0dul connectors on the badge. This gives you maximum mechanical stability and a balanced weight distribution. As the connector on both sides are rotated by 180 degrees you can mount the m0dul 180 degrees rotated. 
 + 
 +{{:​m0dul-dual.brd.png?​direct&​200|}} 
 + 
 +==== Single M0duls ==== 
 +A single m0dul only uses one m0dul connector. These m0duls go to the side of the badge. By rotating the m0dul you can chose to either mount it on the left or the right side of the r0ket. 
 + 
 +{{:​m0dul-single.brd.png?​direct&​200|}} 
 ==== M0dulbus ==== ==== M0dulbus ====
 Connector: 2x06 female socket (2.54mm/​100mil) Connector: 2x06 female socket (2.54mm/​100mil)
  
-{{:r0ket-bus-m0dul.png?200&direct |}}+{{:r0ket-m0dulbus.png?400&​direct| }}
  
 ^ Pin ^ Description ^ ^ Pin ^ Description ^
Line 40: Line 52:
 | SSx | Chip select for SPI or general purpose IO | | SSx | Chip select for SPI or general purpose IO |
 | BUSINT | Active LOW open-drain interrupt ​ | | BUSINT | Active LOW open-drain interrupt ​ |
- 
  
 ====== Software ====== ====== Software ======
m0dul.txt · Last modified: 2011/12/30 00:10 by emdete